Fiber

hard case fiber optical preparation tool kit

FOCCUS Fiber Optic Swabs are specially designed to clean connectors, sleeves and fusion splice mirrors and v-grooves. The swab heads are made of lint-free materials without binders and other contaminates, so it’s clean the 1st time…every time!

Optical Light Source SM & MM

LAN/WAN Access OTDR OPTIMIZED FOR MULTIMODE AND SINGLEMODE ACCESS NETWORK TESTING

Lynx2 splice-on Connectors FC - ST - LC - SC - MPO multi and single mode

Unique design for Master, Expansion and Remote shelves Intuitive and modular architecture adapted to all control office sizes Up to 60 protected (1:1) outputs with 3U shelf and up to 200 protected (1:1) outputs with 6U shelf Expandable System to provide up to 1000 protected outputs Stratum 1 PRS with optional GPS card(s) Choice of Stratum 2 or Stratum 3E holdovers Universal input & output Card design SSM on complete system (Master, Expansion, Remote) TL1 manageable with Local and Remote intuitive Graphical User Interface Optional NTP and PTP modules NEBS level 3

Single-Ended Dispersion Analyzer (CD/PMD)

Optical Light Source SM & MM

No more network outages as a result of fiber detection/identification procedures

The minimized need to access the network helps prevent errors

SONET/SDH, OTN and Ethernet interfaces up to 11.3 Gbit/s Packet synchronization turn-up and troubleshooting (SyncE/1588 PTP) Fibre Channel networks 1x, 2x, 4x, 8x and 10x interfaces. OTN testing (as per ITU-T G.709) bidirectional EtherSAM (ITU-T Y.1564) RFC 2544, multistream. TCP throughput test based on RFC 6349 OTDR: Dynamic range up to either 36 or 39 dB Combined singlemode/multimode wavelengths iOLM-ready: one-touch multiple acquisitions

Optical POWER METER 40 calibrated wavelengths + USB

Hand held Cleaver with off-cut collector and auto-rotating blade

Tool to Remove Cable Jackets and to Open/Score Fiber Tubes

Latest generation of SSU with 6U, 19” or ETSI shelves Intuitive and modular architecture adapted to all telecom node sizes Up to 200 protected (1:1) E1/2.048MHz outputs Expandable System to provide up to 1000 protected outputs (1:1) G.811 PRC with optional dual GPS and/or GLONASS cards and G.812 Type I, II or III SSU holdovers Universal Output & Input card design Fully manageable with intuitive Local and Remote Graphical User Interface Optional NTP and PTP modules 1:1 Protection for every card and function

• Fiber Certifier OLTS (Loss and ORL) with 7-inch tablet-inspired design
• Certifies two fibers at two wavelengths under 3 seconds
• Built-in Encircled-Flux compliancy as per ANSI/TIA and ISO/IEC
• 100% automated fiber inspection:
• One-step process with pass/fail analysis at both ends of the fiber
• Certifies against multiple industry standards

Distributed PMD Analyzer — FTB-5600

FIP-400B Wireless. Fully automated WiFi enabled Fiber Inspection Probe with embedded analysis.

• Bright red laser at 635 nm
• Pulsed and CW
• operation 50 hours of operation (typical)
• Standard AAA alkaline batteries
• Rugged and weatherproof
• 2.5 mm universal connector
• GP-1008 2.5mm to 1,25mm adaptor

• Induces minimal loss: ≤1 dB
• Fail-safe detection and results
• Detects if a fiber is active or not prior to maintenance
• Locates a particular dark fiber using tone recognition (270 Hz, 1 kHz, 2 kHz)
• Identifies traffic direction on a live fiber
• Displays the power transmitted through the fiber
• Three times faster test time

OPTICAL, ETHERNET AND MULTISERVICE TESTER

Optical POWER METER 10 calibrated wavelengths

Hand held Cleaver with off-cut collector and auto-rotating blade

Is discontinued and replaced by model FC-8R

The OSA 5410 Series is a family of compact and cost- effective synchronization distribution and assurance devices that bring the power of Syncjack™ to any network.

Is discontinued and replaced by model Maxtester 940

PMD AND CD ANALYZERS

Fiber Inspection Probe